Re: [OMC-Boats] Engine RPM and Boat Speed.

Thank you everyone for your help. I appreciate it greatly!
Glad to know I'm not alone in this boat restoration project.
 
Here is what I have done so far in hopes of correcting the problem.
 
I have checked the Ohms resistance going to the forward shift coil in the lower unit, the Ohms resistance is 6.1.
I have Installed a new OMC Aluminium Propeller 14 x 18 pitch.
I have plenty of power to reach 4300 - 4500 Rpm's on the tackomater with the 14 x 18 propeller.
I have compared the boats speedometer to a GPS and was amazed at how accurate the boats speedometer is. (When I'm going 17 mph on the speedometer the GPS reads 18 mph)
The bottom of the boat hull has absolutely no barnicles, it has been run in fresh water lakes only.
This Morning I re-waxed the bottom of the boat and obtain only about 2 additional MPH's (26 MPH).
The motor runs very smooth, all 6 cylinders.
We have 2 people in the boat (me and my father).
Fuel tank reads 3/4 tank.
My location is 1200 feet above sea level.
 
I have launched my boat in the lake, tied it to the dock, and let it float for 8 hours unused.
When I returned 8 hours later the boat had not sunk any deeper into the water then when I first launched it. I placed several water line marks on the outside hull with a felt tip marker to tell if any changes occured.
 
This morning after our test run the Boat and Trailer weighed in at 3,040 lbs (by themselves on the public scale).
The Boat Trailer I guesstimate is about 700 lbs.
Accordingly My boat weights in at about 2,340 lbs.
I see no water inside the boat.
 
Question, What RPM's should I be reaching to comfortably cruise down the lake without causing damage to my 155hp engine.. and whys so slow at 4,000 rpm. (26 MPH)
 
Help, Anyboady....
 
Thanks Don.
 
 
 
 
Tue, 22 Jul 2008 12:30:33 -0600From: lee.k.shuster@...: omc-boats@...lists.ultimate.comSubject: Re: [OMC-Boats] Engine RPM and Boat Speed.

I left out a couple of important points:
 
1) Assumption A: I assume you have accurately measured your "true" speed. Using a GPS or an accurately measured and marked-off course? Verify the Pitot is accurate or not partially obstructed. (My experience is they are surprisingly accurate - but still check/verify.)
 
2) Observation B: Something is way off here. Your boat with a 90 hp engine would top 30+ mph new, lightly loaded. Either your V6 is only hitting on 3 cylinders, or there is literally a ton of weight or maybe a ton of barnacles or some combination of all three?
 
3) Observation C: Your observed engine RPM of 3700 is not allowing the engine to deliver it's peak horsepower. Could be many reasons for that. I'd start by incrementally dropping your prop pitch, 18", 16" 14" 12" until your can achieve 4300-4500 RPM at WOT (Wide Open Throttle). The SST (Stainless Steel props are more efficient (less flex) and are available in add pitches (19, 17, 15, 13). The best running props are in the middle pitch ranges, not the extremes.
 
4) Probably not a bad idea to weigh the boat/trailer on a public scale, take out as much junk as possible, and unhook from tow vehicle.
I have a online website calculator that you can plug in variable data: http://hhscott.com/evinrude/docs/BSLAC.htm
 
the calculator takes several variables into consideration and calculates a THEORETICAL top speed. It has been verified against factory published information and in the real world using my 1966 Sportsman with both the Buick V6 and the Chevy V8.
 
Here's what I come up with for your boat (making assumptions that may not be right):
 
Since 3700 RPM is OVER PITCHED for your power-to-weight ratio, you either are down on power or up on weight. For this calculation we will assume a little of both.
 
HP -- 140 hp
Empty Hull Weight: 1975 lbs
Crew Weight: 2 @... 170 lbs ea
Fuel and Gear: 16 gal Fuel @... 7 lbs/gal = 112 lbs, plus 58 lbs misc safety gear
Altitude Above Sea Level : 1000' ASL
Hull Eff Factor = 175 (constant factor verified for a clean, smoothly waxed 1964 - 1968 16ft E/J 16 ft Tri-hull)
 
The Calculated Result: 34 mph
 
 
So to drop another 9 mph you have to add quite a bit more weight, and/or be at a higher altitude, and/or have a "dirty" hull, and/or being carrying more passengers, and/or be producing less power.
 
(Factory specs say your boat, with 1 crew and half a tank of fuel at Sea Level would do about 39 mph on an AL 14x18 prop at around 4300 RPM.)
 
Have fun punching in your own data. I suspect weight is your enemy (but that alone should not bring you down that bar), possibly also look at your engine and prop combo and then clean and wax that hull.
 
Lee Shuster
Salt City - Utah
 
 
 
 

From: omc-boats-bounces@... [mailto:omc-boats-bounces@...ultimate.com] On Behalf Of Don MandelasSent: Tuesday, July 22, 2008 1:12 AMTo: Evinrude & Johnson Boats of the 1960's and 70'sSubject: Re: [OMC-Boats] Engine RPM and Boat Speed.
I have a 1967 Evinrude Sportsman boat with the V-6 155 hp engine. On the stern drive unit I have installed the 14 x 18 propeller. When the engine reaches 3700 RPMs how fast generally should I be traveling across the water? It seems lately that I am going slower than normal (about 25 mph).

Stay in touch when you're away with Windows Live Messenger. IM anytime you're online.
_________________________________________________________________
Use video conversation to talk face-to-face with Windows Live Messenger.
http://www.windowslive.com/messenger/connect_your_way.html?ocid=TXT_TAGLM_WL_Refresh_messenger_video_072008
Received on Tuesday, 22 July 2008